Fin-nor work

quack quack · 04-21-2006, 09:29 AM

Is there anyone in the Boca or west palm area that works on Fin-nor reels.I just got an older 10/0 that I would like gone through.Are there new drags available?I can do most reel work myself but might need some parts or advice.

Islander · 04-21-2006, 04:31 PM

QQ; Hey bud, how it going, haven't been on in awhaile (still working on my house) I'm not sure who still is doing repairs and tune ups. Its been a number of years since I worked at Fin-nor, if I can be of any help just let me know. I did see a post on FS forum about the same questions you asked and there was some feed back, I will see what I can dig up

quack quack · 04-21-2006, 04:41 PM

Thank you very much.Any info would be great.The reel is in nice shape just some battle marks and dried up cosmolene on it.It was serviced at fin-nor many yrs ago and stored.

Another Grand · 04-21-2006, 04:49 PM

QQ.....if you just need them serviced as in lubed and oiled, I got a guy for you but if you are looking for actual drag washers and chit I have heard the only guy that works on them, works at Baitbusters.....I am not sure just word of mouth, but worth a call. Let me know if you just need serviced.

Johnny

Islander · 04-21-2006, 06:26 PM

Yea the drag washers our made of Cork glued on to the brake disk under pressure an at high temperature, then turned on a lathe to spec. Then hand tuned for drag tolerances. I can honestly say there are no two reels exactly alike, because of all the bench adjustment that had to be preformed on each and every reel that left the factory ,excluding the Ahab reels,which were a production reel, and in the beginning well ahead of thie time, and also way to rushed to production, by Japanese standards (AND MINE), who owned the company during my time there as the operations manger, but thats a whole different story in it self

hannaman · 04-21-2006, 08:54 PM

I have a Fin-Nor Ahab 50 wide reel and its awsome. I had to get it repaired a few times to get the drag tweeked out, but now its flawless. I had to ship it to the guy who works for Fin Nor repair service. If you go to the FinNor website you can find the service departments phone # and address.

quack quack · 04-24-2006, 09:15 AM

Thanks for the info guys

04-21-2006, 09:29 AM	#1 (permalink)
quack quack Old Salt Join Date: Nov 2005 Location: lake worth Best Catch: 25lb codfish 5 yrs old first hanger Posts: 4,984	Fin-nor work Is there anyone in the Boca or west palm area that works on Fin-nor reels.I just got an older 10/0 that I would like gone through.Are there new drags available?I can do most reel work myself but might need some parts or advice. __________________ Either we can be a part of the solution or we can be the victims of a decision.

04-21-2006, 04:41 PM	#3 (permalink)
quack quack Old Salt Join Date: Nov 2005 Location: lake worth Best Catch: 25lb codfish 5 yrs old first hanger Posts: 4,984	Thank you very much.Any info would be great.The reel is in nice shape just some battle marks and dried up cosmolene on it.It was serviced at fin-nor many yrs ago and stored. __________________ Either we can be a part of the solution or we can be the victims of a decision.

04-21-2006, 08:54 PM	#6 (permalink)
hannaman Charter Captain Join Date: May 2004 Location: Ft. Lauderdale, Florida Boat: 32 Donzi w/ twins Best Catch: 300+ pound Swordfish club, still. Occupation: Charter Boat Captain Posts: 672	I have a Fin-Nor Ahab 50 wide reel and its awsome. I had to get it repaired a few times to get the drag tweeked out, but now its flawless. I had to ship it to the guy who works for Fin Nor repair service. If you go to the FinNor website you can find the service departments phone # and address. __________________ Captain Cary Hanna New Lattitude SportFishing Charters 954-907-0967 Florida Fishing Charters

04-24-2006, 09:15 AM	#7 (permalink)
quack quack Old Salt Join Date: Nov 2005 Location: lake worth Best Catch: 25lb codfish 5 yrs old first hanger Posts: 4,984	Thanks for the info guys __________________ Either we can be a part of the solution or we can be the victims of a decision.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-21-2006, 04:31 PM	#2 (permalink)
Islander Hooked Up Join Date: Oct 2005 Location: Vero Beach, FL. Boat: FISHING Best Catch: The next one Posts: 197	QQ; Hey bud, how it going, haven't been on in awhaile (still working on my house) I'm not sure who still is doing repairs and tune ups. Its been a number of years since I worked at Fin-nor, if I can be of any help just let me know. I did see a post on FS forum about the same questions you asked and there was some feed back, I will see what I can dig up

04-21-2006, 04:49 PM	#4 (permalink)
Another Grand Grander Join Date: Mar 2005 Posts: 1,093	QQ.....if you just need them serviced as in lubed and oiled, I got a guy for you but if you are looking for actual drag washers and chit I have heard the only guy that works on them, works at Baitbusters.....I am not sure just word of mouth, but worth a call. Let me know if you just need serviced. Johnny

04-21-2006, 06:26 PM	#5 (permalink)
Islander Hooked Up Join Date: Oct 2005 Location: Vero Beach, FL. Boat: FISHING Best Catch: The next one Posts: 197	Yea the drag washers our made of Cork glued on to the brake disk under pressure an at high temperature, then turned on a lathe to spec. Then hand tuned for drag tolerances. I can honestly say there are no two reels exactly alike, because of all the bench adjustment that had to be preformed on each and every reel that left the factory ,excluding the Ahab reels,which were a production reel, and in the beginning well ahead of thie time, and also way to rushed to production, by Japanese standards (AND MINE), who owned the company during my time there as the operations manger, but thats a whole different story in it self

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Looking for work in the Northeast	Bucky	Introductions	0	01-30-2006 09:13 PM
Looking for work in New England	Bucky	Introductions	1	01-30-2006 11:12 AM
No, I don't work for Avet, but...	mmafan	Rigging Corner	26	12-29-2005 02:58 PM
First of all, I don't work for Avet, but...	mmafan	General Fishing Chat	6	12-14-2005 12:20 AM
First of all, I don't work for Avet, but...	mmafan	Shark Fishing	0	12-12-2005 10:39 AM